Surface Treatment of Dental Mini-Sized Implants and Screws: A Systematic Review with Meta-Analysis.

Miniscrews are devices that allow for absolute skeletal anchorage. However, their use has a higher failure rate (10-30%) than dental implants (10%). To overcome these flaws, chemical and/or mechanical treatment of the surface of miniscrews has been suggested. There is no consensus in the current literature about which of these methods is the gold standard; thus, our objective was to carry out a systematic review and meta-analysis of the literature on surface treatments of miniscrews. The review protocol was registered (PROSPERO CRD42023408011) and is in accordance with the PRISMA guidelines. A bibliographic search was carried out on PubMed via MEDLINE, Cochrane Library, Embase and Web of Science. The initial search of the databases yielded 1684 results, with 98 studies included in the review, with one article originating from the search in the bibliographic references of the included studies. The results of this systematic review show that the protocols of miniscrew surface treatments, such as acid-etching; sandblasting, large-grit and acid-etching; photofunctionalization with ultraviolet light; and photobiomodulation, can increase stability and the success of orthodontic treatment. The meta-analysis revealed that the treatment with the highest removal torque is SLA, followed by acid-etching. On the other hand, techniques such as oxidative anodization, anodization with pre-calcification and heat treatment, as well as deposition of chemical compounds, require further investigation to confirm their effectiveness.

Bulk-Fill Resins versus Conventional Resins: An Umbrella Review.

Currently, composite resins have become the material of choice for the restoration of posterior teeth. Although bulk-fill resins represent a tempting alternative due to their lower complexity and faster use, some dentists are reluctant to use this material. The objective is to compare the performance of bulk-fill resins and conventional resins in direct restorations of posterior teeth based on the literature. The databases that were used to carry out the research were PubMed/MEDLINE, Embase, the Cochrane Library and the WOS. This umbrella literature review complies with PRISMA standards and assesses the quality of studies using the AMSTAR 2 tool. With the application of the criteria of the AMSTAR 2 tool, the reviews were considered low to moderate. The overall meta-analysis, although without statistical significance, favours mostly the use of conventional resin, as it is about five times more likely to obtain a favourable result than bulk-fill resin. Bulk-fill resins result in a simplification of the clinical process of posterior direct restorations, which is an advantage. The performance in terms of several properties of bulk-fill resins and conventional resins showed that they present similar behaviour.

Three-Dimensional Impression of Biomaterials for Alveolar Graft: Scoping Review.

Craniofacial bone defects are one of the biggest clinical challenges in regenerative medicine, with secondary autologous bone grafting being the gold-standard technique. The development of new three-dimensional matrices intends to overcome the disadvantages of the gold-standard method. The aim of this paper is to put forth an in-depth review regarding the clinical efficiency of available 3D printed biomaterials for the correction of alveolar bone defects. A survey was carried out using the following databases: PubMed via Medline, Cochrane Library, Scopus, Web of Science, EMBASE, and gray literature. The inclusion criteria applied were the following: in vitro, in vivo, ex vivo, and clinical studies; and studies that assessed bone regeneration resorting to 3D printed biomaterials. The risk of bias of the in vitro and in vivo studies was performed using the guidelines for the reporting of pre-clinical studies on dental materials by Faggion Jr and the SYRCLE risk of bias tool, respectively. In total, 92 publications were included in the final sample. The most reported three-dimensional biomaterials were the PCL matrix, ß-TCP matrix, and hydroxyapatite matrix. These biomaterials can be combined with different polymers and bioactive molecules such as rBMP-2. Most of the included studies had a high risk of bias. Despite the advances in the research on new three-dimensionally printed biomaterials in bone regeneration, the existing results are not sufficient to justify the application of these biomaterials in routine clinical practice.

Current Treatment of Cleft Patients in Europe from a Provider Perspective: A Cross-Sectional Survey.

The latest Eurocleft study reported several discrepancies in cleft care. Since then, no critical assessment has been performed. This study aimed to better understand the main strengths and inefficiencies of cleft care within Europe. The Google documents platform was used to create an online survey to investigate several aspects, i.e., provider characteristics, patient profile, services offered, and treatment protocols and complications. Descriptive statistics were calculated. The association between categorical variables was performed using Fisher's exact test. The significance level chosen was 0.05. A total of 69 individuals from 23 European countries completed the survey. Centralized care was the preferred system, and the majority of the countries have an association for cleft patients and professionals (53.6%). The largest percentage of patients was seen in the university hospital environment (Fisher's exact test p < 0.001). The majority of responders (98.6%) reported that an orthodontist was involved in cleft treatment, and 56.5% of them spend 76-100% of their time treating these patients. Despite cleft care having been reconfigured in Europe, a better consensus among the various centers regarding provider characteristics, services offered, and treatment protocols is still required. There is a need for better coordination between clinicians and national/international regulatory bodies.

Velopharyngeal Insufficiency Treatment in Cleft Palate Patients: Umbrella Review.

Velopharyngeal insufficiency may occur as a result of an anatomical or structural defect and may be present in patients with cleft lip and palate. The treatment options presented in the literature are varied, covering invasive and non-invasive methods. However, although these approaches have been employed and their outcomes reviewed, no conclusions have been made about which approach is the gold-standard. This umbrella review aimed to synthesize the current literature regarding velopharyngeal insufficiency treatments in cleft lip and palate patients, evaluating their effectiveness based on systematic reviews. A standardized search was carried out in several electronic databases, namely PubMed via Medline, Web of Science, Cochrane Library, and Embase. The quality of the included studies was evaluated using AMSTAR2 and degree of overlap was analyzed using Corrected Covered Area. Thirteen articles were included in the qualitative review, with only 1 in the non-invasive method category, and 12 in the invasive method category. All reviewed articles were judged to be of low quality. In symptomatic patients, treatment did not solely comprise speech therapy, as surgical intervention was often necessary. Although there was no surgical technique considered to be the gold standard for the correction of velopharyngeal insufficiency, the Furlow Z-plasty technique and minimal incision palatopharyngoplasty were the best among reported techniques.

Reconstruction of Oronasal Fistula with Tongue Flap: A Cleft Palate Report.

Oronasal fistula can persist after conventional secondary alveolar bone graft surgery, which may lead to functional issues, such as regurgitation of fluids from the oral to the nasal cavity. This manuscript describes a clinical case of a patient with a bilateral cleft lip and palate that underwent tongue graft surgery for closure of an oronasal fistula after three failed local mucosa flap surgeries. The multidisciplinary treatment was comprised of orthodontic treatment, mucosa and alveolar grafts for palate closure and aesthetic rehabilitation of the anterior maxillary teeth. Smile aesthetics were noticeably improved, enhancing the patient's self-perception and confidence.

Application of Three-Dimensional Digital Technology in Orthodontics: The State of the Art.

Three-dimensional technologies are one of the most recent and relevant advancements in the field of Dentistry. These systems, including intraoral scans, 3D imaging exams (CAT scan, CBCT and MRI), CAD/CAM 3D printing devices and 3D computer software, have enabled clinicians to greatly improve patient care along with reducing treatment planning time. The present descriptive study aims to explore possible applications of 3D technologies during the diagnosis, treatment plan, case monitoring and result assessment in orthodontics. The overall upgrade provided by these technologies can improve the clinicians' workflow and effectiveness by simplifying conventional techniques considered to be especially arduous.

The Biological Effects of 3D Resins Used in Orthodontics: A Systematic Review.

Three-dimensional (3D) resin medical-dental devices have been increasingly used in recent years after the emergence of digital technologies. In Orthodontics, therapies with aligners have gained popularity, mainly due to the aggressive promotion policies developed by the industry. However, their systemic effects are largely unknown, with few studies evaluating the systemic toxicity of these materials. The release of bisphenol A and other residual monomers have cytotoxic, genotoxic, and estrogenic effects. This systematic review aims to analyze the release of toxic substances from 3D resins used in Orthodontics and their toxic systemic effects systematically. The PICO question asked was, "Does the use of 3D resins in orthodontic devices induce cytotoxic effects or changes in estrogen levels?". The search was carried out in several databases and according to PRISMA guidelines. In vitro, in vivo, and clinical studies were included. The in vitro studies' risk of bias was assessed using the guidelines for the reporting of pre-clinical studies on dental materials by Faggion Jr. For the in vivo studies, the SYRCLE risk of bias tool was used, and for the clinical studies, the Cochrane tool. A total of 400 articles retrieved from the databases were initially scrutinized. Fourteen articles were included for qualitative analysis. The risk of bias was considered medium to high. Cytotoxic effects or estrogen levels cannot be confirmed based on the limited preliminary evidence given by in vitro studies. Evidence of the release of bisphenol A and other monomers from 3D resin devices, either in vitro or clinical studies, remains ambiguous. The few robust results in the current literature demonstrate the absolute need for further studies, especially given the possible implications for the young patient's fertility, which constitutes one of the largest groups of patients using these orthodontic devices.

What Is the Most Effective Technique for Bonding Brackets on Ceramic-A Systematic Review and Meta-Analysis.

Background: There has been an increase in demand for orthodontic treatment within the adult population, who likely receive restorative treatments using ceramic structures. The current state of the art regarding the most effective method to achieve an appropriate bond strength of brackets on ceramic surfaces isn't consensual. This systematic review aims to compare the available surface treatments to ceramics and determine the one that allows to obtain the best bond strength. Methods: This systematic review followed the PRISMA guidelines and the PICO methodology was used, with the question "What is the most effective technique for bonding brackets on ceramic crowns or veneers?". The research was carried out in PubMed, Web of Science, Embase and Cochrane Library databases. In vitro and ex vivo studies were included. The methodological quality was evaluated using the guidelines for reporting of preclinical studies on dental materials by Faggion Jr. Results: A total of 655 articles searched in various databases were initially scrutinized. Sevety one articles were chosen for quality analysis. The risk of bias was considered medium to high in most studies. The use of hydrofluoric acid (HF), silane and laser afforded the overall best results. HF and HF plus laser achieved significantly highest bond strength scores in felsdphatic porcelain, while laser was the best treatment in lithium disilicate ceramics. Conclusions: The most effective technique for bonding brackets on ceramic is dependent on the type of ceramic.

A New Orthodontic-Surgical Approach to Mandibular Retrognathia.

(1) Background: Mandibular deficiency is one of the most common growth disorders of the facial skeleton. Recently, distraction osteogenesis has been suggested as the treatment of choice for overcoming the limitations of conventional orthognathic surgery; (2) Methods: A new custom-manufactured dental-anchored distractor was built and anchored in the first molar and lower canine. It consists of a stainless-steel disjunction screw, adapted and welded to the orthodontic bands through two 1.2 mm diameter connector bars with a universal silver-based and cadmium-free solder; (3) Results: The distractor described can be a useful tool to correct mandibular retrognathia and is better tolerated by patients, especially in severe cases; (4) Conclusions: The dental-anchored distractor increases the anterior mandibular bone segment without affecting the gonial angle or transverse angulation of the segments and avoids posterior mandibular rotation, overcoming the limitations of conventional surgical treatment.

Apical Sealing Ability of Two Calcium Silicate-Based Sealers Using a Radioactive Isotope Method: An In Vitro Apexification Model.

The aim of this study was to evaluate and compare the sealing ability of two calcium silicate-based sealers (TotalFill BC RRM Fast Set Putty and White ProRoot MTA) when used as apical plugs in immature teeth through nuclear medicine. Single-rooted extracted teeth (n = 34) had their crowns and root tip sectioned to obtain 14 mm long root segments to simulate an in vitro apexification model. Were created two experimental groups, namely MTA (n = 12) and BC (n = 12), and two control groups, PG (positive group, n = 5) and NG (negative group, n = 5). On the 4th day after placing the respective apical plug, the apical portions of the teeth were submerged in a solution of sodium pertechnetate (99mTcNaO4) for 3 h. Statistical analysis showed a significant difference between the MTA group and the controls (p < 0.05). The BC group had a significant difference regarding the negative control (p < 0.001) but showed no statistical significance regarding the positive control (p = 0.168). There was a statistically significant difference (p = 0.009) between the BC group (7335.8 ± 2755.5) and the MTA group (4059.1 ± 1231.1), where the last showed less infiltration. Within the limitations of this study, White ProRoot MTA had a significantly better sealing ability than TotalFill BC RRM Fast Set Putty.

Resin infiltration in white spot lesions caused by orthodontic hypomineralisation: a minimally invasive therapy.

Objective White spot lesions are characterised by the presence of clinically detectable opaque lesions due to enamel demineralisation. These frequently present in patients following fixed orthodontic treatment, mostly due to the prolonged accumulation of bacterial plaque on the dental surface. When remineralisation is not achieved through good oral hygiene and prophylaxis with fluoride products, the infiltration of lesions with low-viscosity photopolymerised resin has proved to be a valid micro-invasive alternative compared to traditional conservative therapy.Clinical considerations A case series will be presented, where the chosen approach was resin infiltration, a micro-invasive and aesthetic technique.Clinical significance Infiltrative resin therapies are single-session procedures that reduce the need for more invasive therapies such as the use of rotary instruments for greater patient comfort. The need for periodic fluoride applications is also avoided. This approach increases the durability of the infiltrated lesion without compromising its mechanical properties and impedes the development of recurrent or secondary caries.Conclusions Resin infiltration might be considered as a routine procedure in the treatment of post-eruptive hypomineralised lesions. This follows the line of thought of minimally invasive dentistry, is an excellent treatment option and prevents the lesion's progression.

Accessing the Cytotoxicity and Cell Response to Biomaterials.

Biomaterials contact directly or indirectly with the human tissues, making it important to evaluate its cytotoxicity. This evaluation can be performed by several methods, but a high discrepancy exists between the approaches used, compromising the reproducibility and the comparison among the obtained results. In this paper, we propose a protocol to evaluate biomaterials cytotoxicity using soluble extracts, which we use for dental biomaterials. The extracts preparation is detailed, from pellets production to its extraction in a culture medium. The biomaterials cytotoxicity evaluation is based on metabolic activity using the MTT assay, cell viability using the Sulphorhodamine B (SBR) assay, cell death profile by flow cytometry, and cell morphology using May-Grünwald Giemsa. Additional to cytotoxicity evaluation, a protocol to evaluate cell function is described based on the expression of specific markers assessed by immunocytochemistry and PCR. This protocol provides a comprehensive guide for biomaterials cytotoxicity and cellular effects evaluation, using the extracts methodology, in a reproducible and robust manner.

Regenerative Strategies in Cleft Palate: An Umbrella Review.

(1) Background: Alveolar bone defects or decreased alveolar bone height and width may have different causes, such as cleft palate. Regenerative procedures in oro-dental defects are challenging due to anatomical factors and the distinct cell populations involved. The iliac crest bone graft remains the gold-standard for cleft palate closure. However, tissue regeneration approaches have been employed and their outcome reviewed, but no conclusions have been made about which one is the gold-standard. (2) Methods: this umbrella review aims to critically appraise the effectiveness of the current approaches in bone defects regeneration in non-syndromic patients with cleft palate. A search was performed in PubMed, Cochrane Library, Scopus, Web of Science and EMBASE databases. (3) Results: Systematic reviews of randomized and non-randomized controlled trials with or without meta-analysis were included. Nine articles were included in the qualitative analysis and five in the quantitative one. The included studies quality was evaluated with AMSTAR2. (4) Conclusions: The use of new regenerative strategies, such as bone morphogenic protein 2, appears to provide similar results regarding bone volume, filling, and height to the standard technique with the iliac crest bone graft.

Effect of Different Irrigation Solutions on the Diffusion of MTA Cement into the Root Canal Dentin.

(1) Aim: This study aims to analyze the in vitro infiltration of a silicate root canal sealer into dentinal tubules after using different endodontic irrigating solutions. (2) Methods: Twenty-nine teeth with single roots were separated into three groups according to the final irrigation protocol: G1 n = 10) = 17% EDTA (ethylenediaminetetraacetic acid) + 3.0% sodium hypochlorite (NaOCl), G2 (n = 10) = 17% EDTA + 2.0% chlorhexidine and G3 (Control group, n = 9) = 17% EDTA + saline solution. Root canals were filled using cold lateral compaction technique with MTA Fillapex sealer and gutta-percha. The sealer was labeled with rhodamine B. The teeth were segmented at the middle and third apical sections, which were visualized using 10× confocal laser microscopy to determine the sealer penetration percentage. (3) Results: In the apical section, no statistically significant differences were found between the groups regarding sealer penetration. In the middle section, Group 1 obtained the highest percentage, and Group 2 the lowest (p = 0.004). Group 1 also presented statistically significant differences in the Control Group (p = 0.031) and had close sealer penetration values. Meanwhile, the Control Group (p = 0.023) and Group 2 (p = 0.029) revealed a significant decrease of sealer penetration between the apical and middle sections. (4) Conclusion: The obtained results support that final irrigation with NaOCl promoted similar sealer penetration in the apical and middle sections. On the other hand, a significant decrease in the sealer penetration of the middle section was observed for the chlorhexidine and saline groups. Compared to other irrigant solutions, NaOCl promotes more uniform sealer penetration, which can correlate with better sealing and, consequently, higher endodontic treatment success.

Mechanical and Tribological Characterization of a Dental Ceromer.

BACKGROUND: Indirect restorations using composites with ceramic fillings can be an alternative to ceramic veneering and direct composite restorations for the treatment of posterior teeth. The aim of this study was the evaluation of the mechanical and tribological properties of a ceromer. MATERIALS AND METHODS: Sixty specimens were produced and divided into two groups: one control group not submitted to thermocycling (n = 20) and one test group submitted to 5000 cycles of thermocycling (n = 40). The studied parameters were microhardness, surface roughness and the coefficient of friction (scratch test). RESULTS: The ceromer exhibits a reduction of polymerization shrinkage, higher wear, and fracture resistance than the composite resins. The studied ceromer presented good mechanical properties, even after being submitted to thermocycling. Roughness was the property most affected, increasing 25.8%, microhardness decreased by 10.5% and the coefficient of friction increased by 4.2%. CONCLUSIONS: In certain situations, ceromers can be an alternative to composite resins and ceramics, providing an aesthetic, conservative and longevity option.

Biocompatibility of Root Canal Sealers: A Systematic Review of In Vitro and In Vivo Studies.

(1) Aim: To perform a systematic review of the literature on the biocompatibility of root canal sealers that encompasses the various types of sealers that are commercially available as well as both in vitro and in vivo evidence. (2) Methods: This systematic review has been registered in PROSPERO (ID 140445) and was carried out according to PRISMA guidelines using the following databases: PubMed, Cochrane Library, ClinicalTrials.gov, Science Direct, and Web of Science Core Collection. Studies published between 2000 and 11 June 2019 that evaluated cytotoxicity (cell viability/proliferation) and biocompatibility (tissue response) of root canal sealers were included. (3) Results: From a total of 1249 studies, 73 in vitro and 21 in vivo studies were included. In general, studies suggest that root canal sealers elicit mild to severe toxic effects and that several factors may influence biocompatibility, e.g., material setting condition and time, material concentration, and type of exposure. Bioactive endodontic sealers seem to exhibit a lower toxic potential in vitro. (4) Conclusions: The available evidence shows that root canal sealers exhibit variable toxic potential at the cellular and tissue level. However, the methodological heterogeneity among studies included in this systematic review and the somewhat conflicting results do not allow a conclusion on which type of sealer presents higher biocompatibility. Further research is crucial to achieve a better understanding of the biological effects of root canal sealers.

Synthetic Calcium Phosphate Ceramics as a Potential Treatment for Bisphosphonate-Related Osteonecrosis of the Jaw.

(1) Background: Bisphosphonate-related osteonecrosis of the jaw (BRONJ) is one of the most often seen side effects in patients treated with nitrogen-containing bisphosphonates (BPs), a post-surgical non-healing wound condition. Since calcium phosphate (CP) compounds are able to adsorb zoledronate (ZOL) when used as a drug delivery vehicle, we aimed to verify if these ceramics might have a potential protective effect for soft tissues surrounding surgical osseous wounds. (2) Methods: The chemical reaction between ZOL and CP compounds was evaluated through ultraviolet-visible spectroscopy and elemental analysis. A primary culture of human gingival fibroblasts (HGF) was established as a model to evaluate the cytotoxicity of the association of ZOL (5-500 µM) and of ZOL/biphasic calcium phosphates (BCP). Metabolic activity, cell viability, types of cell death, the cell cycle through, and the migration ability of human gingival fibroblasts were evaluated. (3) Results: ZOL was adsorbed by biphasic calcium phosphate compounds in an aqueous solution. The HGF were sensitive to ZOL toxicity; nevertheless, ZOL/BCP showed a significant protective effect regarding metabolic activity, cell viability, and cell migration. (4) Conclusions: BCP interaction with ZOL reduces or abolishes its toxicity in HGF. This finding represents a potential solution for BRONJ in the case of patients undergoing therapy with ZOL.

Once Resin Composites and Dental Sealants Release Bisphenol-A, How Might This Affect Our Clinical Management?-A Systematic Review.

(1) Background: Bisphenol A (BPA) based dental resins are commonly used in preventive and reparative dentistry. Since some monomers may remain unpolymerized in the application of dental resin, they dissolve in the saliva. (2) Methods: The literature search was carried out in Pubmed, Cochrane and Embase databases. Randomized controlled trials, cohort studies and case-control studies that evaluated BPA levels in human urine, saliva and/or blood were included. (3) Results: The initial search had 5111 results. A total of 20 studies were included in the systematic review. Most studies showed an increase of the levels of bisphenol A 1 h after treatments with composite resins and dental sealants. One week after treatments the levels were decreased. (4) Conclusions: Some clinical precautions should be taken to decrease the release of BPA, namely the use of rubber dam, the immediate polishing of all resins used, or the use of glycerin gel to avoid non-polymerization of the last resin layer, and mouthwash after treatment. Another preventive measure in addition to the above-mentioned is the use of the smallest possible number of restorations or sealants, a maximum of four per appointment. These measures are even more important in children, adolescents and pregnant women.

Chlorhexidine mouthwash as an anticaries agent: A systematic review.

OBJECTIVE: To evaluate the effectiveness of chlorhexidine mouthwashes on the reduction of cariogenic bacteria on patients with moderate to high risk for dental caries. DATA SOURCES: A systematic review of the literature was performed using Cochrane Library, Embase, PubMed, Scopus and Web of Science. The search was limited to articles in English, Spanish, and Portuguese, published until January 2017. The research question was formulated following the PICO strategy. The risk of bias was evaluated using the guidelines of the Cochrane Handbook for Systematic Reviews of Interventions. CONCLUSION: All the authors found statistically significant differences in Streptococcus mutans levels during and after the use of a chlorhexidine mouthwash. Although the results are suggestive, there is a clear need for the development of new studies with higher quality and with longer follow-ups, in order to assess whether the results translate into less development of dental caries and, consequently, whether or not these products should be incorporated into prevention protocols.